Guru filer (labb webbserver)
INITSYS.NCF (SYS:ETC\)
#! --- WARNING -- WARNING -- WARNING -- WARNING -- WARNING
-- WARNING ----
#! This file was created by the Internetworking Configuration Console.
#! It is intended to be modified ONLY by the configurator (INETCFG.NLM).
#! Tampering with this file may cause severe malfunctioning of the system.
#! The configurator will check for tampering and abort if it is detected.
#! -----------------------------------------------------------------------
load snmp config=Sys:Etc
initialize system
NETINFO.CFG (SYS:ETC\)
#!VERSION=2.2
#!
#! --- WARNING -- WARNING -- WARNING -- WARNING -- WARNING -- WARNING
----
#! This file was created by the Internetworking Configuration Console.
#! It is intended to be modified ONLY by the configurator (INETCFG.NLM).
#! Tampering with this file may cause severe malfunctioning of the system.
#! The configurator will check for tampering and abort if it is detected.
#! -----------------------------------------------------------------------
#!
#!SERVERTYPE=NORMAL
#!SERVERNAME=SICILY
#!
#!BEGINGENLOAD
LOAD SNMP
#!END
#!
#!BEGINTSMLOAD
#!END
#!
#!BEGINBOARD DRVR=DLKFET NAME=DLKFET_1 STATUS=ENABLED NUMPORTS=1 DRVRTYPE=LAN
VARIABLEPORTS=NO PORTPARAM=CHANNEL SLOT=3
#Transferred from AUTOEXEC.NCF
#!BEGINPORT NAME=DLKFET_1 NUMBER=1 STATUS=ENABLED FRAMES=YES NUMLINKS=1
MEDIA=EtherTsm WANFRAME=UNCONFIGURED
#Transferred from AUTOEXEC.NCF
#!REFCOUNT=2
LOAD DLKFET NAME=DLKFET_1_E83 FRAME=ETHERNET_802.3 SLOT=3
#!REFCOUNT=2
LOAD DLKFET NAME=DLKFET_1_E82 FRAME=ETHERNET_802.2 SLOT=3
#!REFCOUNT=2
LOAD DLKFET NAME=DLKFET_1_EII FRAME=ETHERNET_II SLOT=3
#!END
#!END
#!
#!BEGINPROTO PROTO=TCPIP STATUS=ENABLED
LOAD Tcpip RIP=No Forward=No
#
LOAD IPConfig Screen=no
#
#!BEGINBIND STATUS=ENABLED
BIND IP DLKFET_1_EII MASK=FF.FF.FF.0 ADDRESS=195.100.57.168
#195.100.57.168
#!END
#!END
#!
#!BEGINPROTO PROTO=IPX STATUS=ENABLED
LOAD IPXRTR ROUTING=NLSP
#Transferred from AUTOEXEC.NCF
#!BEGINBIND STATUS=ENABLED
BIND IPX DLKFET_1_E82 NET=A
#A
#!END
#!BEGINBIND STATUS=ENABLED
BIND IPX DLKFET_1_E83 NET=C31
#C31
#!END
#!END
STARTUP.NCF (C:\NWSERVER\)
; The following lines were moved or added by the NetWare
Support Pack
LOAD C:\NWSERVER\DIAG411.NLM
LOAD C:\NWSERVER\PK411.NLM
LOAD C:\NWSERVER\CPUCHECK.NLM
; End of modifications made by NetWare Support Pack installation
SET RESERVED BUFFERS BELOW 16 MEG=200
LOAD KEYB Sweden
LOAD IDEATA.HAM INT=E PORT=1F0
LOAD IDEATA.HAM INT=F PORT=170
LOAD IDECD.CDM
LOAD IDEHD.CDM
load MAC
AUTOEXEC.NCF (SYS:SYSTEM\)
set Time Zone = MET-1MEST
set Daylight Savings Time Offset = 1.00.00
set Start Of Daylight Savings Time = (MARCH SUNDAY LAST 2.00.00 )
set End Of Daylight Savings Time = (OCTOBER SUNDAY LAST 3.00.00 )
set Default Time Server Type = SECONDARY
# Note: The Time zone information mentioned above
# should always precede the SERVER name.
set Bindery Context = O=COSANOSTRA
file server name SICILY
ipx internal net 1411702
### VAR REMAT AV INETCFG
LOAD IPXRTR routing=NLSP
LOAD TCPIP
LOAD DLKFET SLOT=3 FRAME=ethernet_802.3 NAME=DLKFET_1_E83
BIND IPX DLKFET_1_E83 NET=C31
LOAD DLKFET SLOT=3 FRAME=ethernet_802.2 NAME=DLKFET_1_E82
BIND IPX DLKFET_1_E82 NET=A
LOAD DLKFET SLOT=3 FRAME=ethernet_II NAME=DLKFET_1_EII
BIND IP DLKFET_1_EII ADDR=195.100.57.168 MASK=ff.ff.ff.0
### END REM
mount all
# The following lines were added by Netscape Server for
NetWare
NSWEB
# End of lines added by Netscape Server for NetWare
load conlog maximum=100
; Network driver LOADs and BINDs are initiated via
; INITSYS.NCF. The actual LOAD and BIND commands
; are contained in INITSYS.NCF and NETINFO.CFG.
; These files are in SYS:ETC.
#sys:etc\initsys.ncf
NSWEB.NCF (SYS:SYSTEM\)
# Startup for the Netscape Enterprise Server for Netware
by Novonyx
# Load cron for automatic updates of indexes, index optimization,
and log rotation
load cron
# Load SNMP agent for network management
load sys:\novonyx\suitespo\plugins\snmp\nssnmp -d /novonyx/suitespot/https-SICILY/config
# Load web server
nvxwebup
# Load administration server
nvxadmup
NSWEBDN.NCF (SYS:SYSTEM\)
# Shutdown for the Netscape Web Server for Netware by
Novonyx
nvxadmdn
nvxwebdn
#unload nssnmp
#unload cron
HOSTS (SYS:ETC\)
#
# SYS:ETC\HOSTS
#
# Mappings of host names and host aliases to IP address.
#
127.0.0.1 loopback lb localhost # normal loopback address
#
# examples from Novell network
#
130.57.4.2 ta tahiti ta.novell.com loghost
130.57.6.40 osd-frog frog
130.57.6.144 sj-in5 in5
192.67.172.71 sj-in1 in1
#
# interesting addresses on the Internet
#
192.67.67.20 sri-nic.arpa nic.ddn.mil nic
26.2.0.74 wsmr-simtel20.army.mil simtel20
195.100.57.168 KCK
SERVMAN.NLM (SYS:SYSTEM\)
TCP Defend Land Attacks = On
Maximum Pending TCP Connection Requests = 128
TCP Defend SYN Attacks = Off
IP Wan Client Validation = Off
Allow IP Address Duplicates = Off
IPX NetBIOS Replication Option = 2
Load Balance Local LAN = Off
Maximum Packet Receive Buffers = 100
Minimum Packet Receive Buffers = 50
Maximum Physical Receive Packet Size = 4202
Maximum Interrupt Events = 10
Reply To Get Nearest Server = On
Number Of Watchdog Packets = 10
Delay Between Watchdog Packets = 59.3
Delay Before First Watchdog Packet = 296.6
New Packet Receive Buffer Wait Time = 0.1
Use Old Watchdog Packet Type = Off
Console Display Watchdog Logouts = Off
Allow Invalid Pointers = Off
Read Fault Notification = On
Read Fault Emulation = Off
Write Fault Notification = On
Write Fault Emulation = Off
Garbage Collection Interval = 900
Number of Frees For Garbage Collection = 5000
Minimum Free Memory For Garbage Collection = 8000
Alloc Memory Check Flag = Off
Auto Register Memory Above 16 Megabytes = On
Reserved Buffers Below 16 Meg = 200
Read Ahead Enabled = On
Read Ahead LRU Sitting Time Threshold = 10
Minimum File Cache Buffers = 20
Maximum Concurrent Disk Cache Writes = 50
Dirty Disk Cache Delay Time = 3.3
Minimum File Cache Report Threshold = 20
Dirty Directory Cache Delay Time = 0.5
Maximum Concurrent Directory Cache Writes = 10
Directory Cache Allocation Wait Time = 2.2
Directory Cache Buffer NonReferenced Delay = 5.5
Maximum Directory Cache Buffers = 500
Minimum Directory Cache Buffers = 20
Maximum Number Of Internal Directory Handles = 100
Maximum Number Of Directory Handles = 20
Minimum File Delete Wait Time = 65.9
File Delete Wait Time = 329.6
Allow Deletion Of Active Directories = On
Maximum Percent of Volume Space allowed for Extended Attributes = 10
Maximum Extended Attributes per File or Path = 16
Fast Volume Mounts = On
Maximum Percent Of Volume Used By Directory = 13
Immediate Purge Of Deleted Files = Off
Maximum Subdirectory Tree Depth = 25
Volume Low Warn All Users = On
Volume Low Warning Reset Threshold = 256
Volume Low Warning Threshold = 256
Turbo FAT Re-Use Wait Time = 329.6
Compression Daily Check Stop Hour = 6
Compression Daily Check Starting Hour = 0
Minimum Compression Percentage Gain = 20
Enable File Compression = On
Maximum Concurrent Compressions = 2
Convert Compressed To Uncompressed Option = 1
Decompress Percent Disk Space Free To Allow Commit = 10
Decompress Free Space Warning Interval = 1878.5
Deleted Files Compression Option = 1
Days Untouched Before Compression = 14
Allow Unowned Files To Be Extended = On
Maximum Record Locks Per Connection = 500
Maximum File Locks Per Connection = 250
Maximum Record Locks = 20000
Maximum File Locks = 10000
Auto TTS Backout Flag = On
TTS Abort Dump Flag = Off
Maximum Transactions = 10000
TTS UnWritten Cache Wait Time = 65.9
TTS Backout File Truncation Wait Time = 3559.2
Enable Disk Read After Write Verify = Off
Remirror Block Size = 1
Concurrent Remirror Requests = 4
Mirrored Devices Are Out Of Sync Message Frequency = 30
Sequential Elevator Depth = 8
Ignore Disk Geometry = Off
Enable IO Handicap Attribute = Off
TIMESYNC ADD Time Source =
TIMESYNC Configuration File = SYS:SYSTEM\TIMESYNC.CFG
TIMESYNC Configured Sources = Off
TIMESYNC Directory Tree Mode = On
TIMESYNC Hardware Clock = On
TIMESYNC Polling Count = 3
TIMESYNC Polling Interval = 600
TIMESYNC REMOVE Time Source =
TIMESYNC RESET = Off
TIMESYNC Restart Flag = Off
TIMESYNC Service Advertising = On
TIMESYNC Synchronization Radius = 2000
TIMESYNC Time Adjustment = None scheduled.
TIMESYNC Time Source =
TIMESYNC Type = SECONDARY
TIMESYNC Write Parameters = Off
TIMESYNC Write Value = 3
Time Zone = MET-1MEST
Default Time Server Type = SECONDARY
Start Of Daylight Savings Time = (MARCH SUNDAY LAST 2.00.00 )
End Of Daylight Savings Time = (OCTOBER SUNDAY LAST 3.00.00 )
Daylight Savings Time Offset = +1:00:00
Daylight Savings Time Status = Off
New Time With Daylight Savings Time Status = Off
NCP File Commit = On
Display NCP Bad Component Warnings = Off
Reject NCP Packets with bad components = Off
Display NCP Bad Length Warnings = Off
Reject NCP Packets with bad lengths = Off
Maximum Outstanding NCP Searches = 51
NCP Packet Signature Option = 1
Enable IPX Checksums = 1
Allow Change To Client Rights = On
Allow LIP = On
Command Line Prompt Default Choice = On
Command Line Prompt Time out = 10
Sound Bell For Alerts = On
Replace Console Prompt With Server Name = On
Alert Message Nodes = 20
Worker Thread Execute In A Row Count = 10
Halt System On Invalid Parameters = Off
Upgrade Low Priority Threads = Off
Display Relinquish Control Alerts = Off
Display Incomplete IPX Packet Alerts = On
Display Old API Names = Off
CPU Hog Timeout Amount = 60
Developer Option = Off
Display Spurious Interrupt Alerts = Off
Display Lost Interrupt Alerts = Off
Pseudo Preemption Count = 10
Global Pseudo Preemption = Off
Minimum Service Processes = 10
Maximum Service Processes = 50
New Service Process Wait Time = 2.2
Automatically Repair Bad Volumes = On
Enable SECURE.NCF = Off
Allow Audit Passwords = Off
Allow Unencrypted Passwords = Off
Server Log File State = 1
Volume Log File State = 1
Volume TTS Log File State = 1
Server Log File Overflow Size = 4194304
Volume Log File Overflow Size = 4194304
Volume TTS Log File Overflow Size = 4194304
Enable Deadlock Detection = Off
Auto Restart After Abend Delay Time = 2
Auto Restart After Abend = 1
NDS trace to screen = Off
NDS trace to file = Off
NDS Trace Filename = SYSTEM\DSTRACE.DBG
NDS client NCP retries = 3
NDS external reference life span = 192
NDS inactivity synchronization interval = 30
NDS synchronization restrictions = OFF
NDS servers status = UP/DOWN
NDS janitor interval = 60
NDS backlink interval = 780
NDS trace file length to zero = Off
NDS do not synchronize with = ON,290,291,296,332,463,477
Additional Security Checks = Off
Check Equivalent To Me = Off
Bindery Context = O=COSANOSTRA
SECURE.NCF (SYS:SYSTEM\)
##########################################################
#
# Version: 1.01
# Date: May 14, 1997
#
# This NetWare script file, SECURE.NCF, is the enhanced
# security options configuration file. It chooses the
# options that are required to run NetWare in the trusted
# configuration, which is designed to meet the US Class
# C2 security criteria and the European Class F-C2/E2
# security criteria.
#
# Enhanced security options not required for the trusted
# configuration (not required by C2 and European Class
# F-C2/E2 standards) are also included in this file but are
# commented out. More information regarding enhanced
# security options may be found in the Enhanced Security
# Server Administration manual.
#
# The server may be configured to automatically execute
# this configuration file during server boot after the
# execution of AUTOEXEC.NCF. This can be done by setting
# the set parameter "Enable SECURE.NCF" to ON. This can
# be done from SERVMAN (Server parameters/Miscellaneous
# menu) or in either AUTOEXEC.NCF or STARTUP.NCF. This
# configuration file can also be executed from the NetWare
# Console command line.
#
# Each of the SET parameters in this file (SECURE.NCF) can
# be set individually from the NetWare console command line,
# from SERVMAN, or in AUTOEXEC.NCF.
#
# SECURE.NCF may be modified using EDIT.NLM or another
# ASCII editor. The file is stored in the SYS:/SYSTEM
# directory.
#
# The following commands are required for the trusted
# configuration. Refer to the Utilities Reference manual
# for more information about each of these commands.
#
# The following command configures the server to disallow
# the use of unencrypted passwords. The default value is
# OFF. The trusted configuration value is also OFF.
#
SET Allow Unencrypted Passwords = OFF
#
# The following command configures the server to disallow
# the use of passwords to identify auditors. The default
# value is OFF. The trusted configuration value is also
# OFF.
#
SET Allow Audit Passwords = OFF
#
# The following command configures the server to
# automatically run VREPAIR when a volume fails to mount.
# The default value is ON. The trusted configuration
# value is also ON.
#
SET Automatically Repair Bad Volumes = ON
#
# The following command configures the server to reject
# NCP packets that fail boundary checking. Older client
# utilities may fail if this SET parameter is set to ON.
# The default value is OFF. The trusted configuration
# value is ON.
#
SET Reject NCP Packets with bad lengths = ON
#
# The following command configures the server to disallow
# replication of NetBIOS broadcast packets. The default
# value is 2. The trusted configuration value is 0.
#
SET IPX NetBIOS Replication Option = 0
#
# The following command configures the server to reject
# NCP packets that fail component checking. Older client
# utilities may fail if this set parameter is set to ON.
# The default value is OFF. The trusted configuration
# value is ON.
#
SET Reject NCP Packets with bad components = ON
#
# The following command configures NetWare Directory
# Services to perform access control checks which are
# not backwards compatiable with previous versions of
# NetWare Directory Services. The default value is OFF.
# The trusted configuration value is ON.
#
SET Additional Security Checks = ON
#
# The above commands are required for your server to be
# in the trusted configuration, designed to meet the
# Class C2 criteria and the Class F-C2/E2 criteria.
#
#########################################################
#########################################################
#
# The following commands provide additional enhanced
# security options that are not required to meet the
# Class C2 criteria and the Class F-C2/E2 criteria.
# These have been commented out but may be enabled by
# removing the comment symbol (# ) from the beginning of
# the line. EDIT.NLM or another ASCII editor may be used
# to edit this file. For more information about each of
# these commands refer to the Utilities Reference manual.
#
# The following command configures NetWare Directory
# Services to enforce the checking of the Equivalent To
# Me attribute during authentication. DSREPAIR must be
# used to synchronize the Equivalence attribute and the
# Equivalent To Me attribute if the Check Equivalent to
# Me parameter is set to ON. Setting this parameter to
# ON will also adversely affect the authentication
# performance. The default value is OFF. For enhanced
# security the value may be set to ON.
#
# SET Check Equivalent to Me = ON
#
# The following command configures the server to reject
# NCP packets that are not signed and to sign all reply
# packets. Setting this parameter to 3 will adversely
# affect the communication performance of the server.
# The default value is 1, which signs NCP packets only if
# required by the client. For enhanced security the
# value may be set to 3.
#
# SET NCP Packet Signature Option = 3
#
# The following command secures the NetWare server
# console in the following ways: it removes DOS paths
# from the search path; it allows only NLMs from the
# search path to be loaded; it disallows the setting of
# certain SET parameters; it prevents the server date and
# time from being changed; and it prevents keyboard entry
# into the operating system debugger. This command does NOT
# remove the requirement that the server console be
# physically secured. By default, SECURE CONSOLE is not
# invoked. For enhanced security SECURE CONSOLE may be
# invoked.
#
# SECURE CONSOLE
#
# The above commands provide enhanced security options
# that are NOT required for your server to be in the
# trusted configuration -- to meet the Class C2
# criteria and the Class F-C2/E2 criteria.
#
###########################################################